Internet PLC Forum
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News:
Home
Help
Search
Login
Register
Internet PLC Forum
»
General
»
Technical support
»
Motor control
« previous
next »
Print
Pages: [
1
]
Author
Topic: Motor control (Read 13085 times)
can
Full Member
Posts: 160
I'm a llama!
Motor control
«
on:
July 28, 2010, 09:18:45 PM »
Hi. Has anybody tried to control the speed of an ac servo motor by using the analogue output to give a voltage to the motor driver? I currently have a motor driver that accepts 0-10vdc as analogue input. I want to use the analogue output of 0-5vdc to control it. The question is that if I activate function setDAC 1,4096, will the motor driver immediately run at full speed? Or should I write a function to accelerateor decelerate the motor by varying the output voltage?
Regards
Can
Logged
support
Global Moderator
Hero Member
Posts: 3174
Re:Motor control
«
Reply #1 on:
July 29, 2010, 09:16:43 AM »
A servo motor should have its own feedback loop so you can simply supply it with a stable voltage it needs.
Since the servo motor driver requires 0-10V you need to give it 10V to run at full speed. You can use the F1616-BA which has built-in 0-10V analog outputs.
If you supply 5V to the servo motor it is most likely going to run only at half speed (depend on what the spec is).
Logged
Email: support@triplc.com
Tel: 1-877-TRI-PLCS
can
Full Member
Posts: 160
I'm a llama!
Re:Motor control
«
Reply #2 on:
July 29, 2010, 09:28:25 AM »
Hi. So do I have to varies the DAC from 0 to 4096 if i want the motor to accelerate smoothly?
Regards
Logged
support
Global Moderator
Hero Member
Posts: 3174
Re:Motor control
«
Reply #3 on:
July 29, 2010, 09:30:41 AM »
I don't think so, but there is nothing to stop you from doing it. The best is to test the dynamic of your system by using a step input first (i.e. apply the voltage in a single step) and if the response is not desirable you can then give it a slope which is easy to do with our PLC.
Logged
Email: support@triplc.com
Tel: 1-877-TRI-PLCS
can
Full Member
Posts: 160
I'm a llama!
Re:Motor control
«
Reply #4 on:
July 29, 2010, 09:31:45 AM »
Ok. Thanks for the quick reply. Will try that out.
Logged
can
Full Member
Posts: 160
I'm a llama!
Re:Motor control
«
Reply #5 on:
July 31, 2010, 12:22:32 AM »
Hi. I have another question. If the servo motor driver output is giving positional signal by A, B, and Z phase, is there anyway a 888 will be able to determine the position by reading the signal?
Regards
Logged
support
Global Moderator
Hero Member
Posts: 3174
Re:Motor control
«
Reply #6 on:
August 02, 2010, 12:02:51 PM »
Are the A B and Z signals analog? If these signal are within the range of the PLC's analog inputs you can certainly read them using the ADC(n) statement.
Logged
Email: support@triplc.com
Tel: 1-877-TRI-PLCS
Print
Pages: [
1
]
« previous
next »
Internet PLC Forum
»
General
»
Technical support
»
Motor control